Setpoint
Most tech mods ask you to build a machine, feed it power and wait. Setpoint asks something different: it asks you to run a plant. Pumps cavitate when starved, boilers trip at 9 bar, tanks fill to their real level, and every piece of equipment has a place on a P&ID drawing just like the ones real operators work from. If you have ever wanted a control room with a mimic board on the wall and an alarm list that actually matters, this is the add-on for you.
What Setpoint Adds to Minecraft
Setpoint is a process engineering mod. At its heart is the P&ID, or piping and instrumentation diagram. Place a blank P&ID sheet, pick two corners, and it draws a plan view of everything inside the box: pumps, tanks, valves and instruments as their proper symbols, pipes as lines, and signal links running from controllers to the valves they command. Hang that sheet in a control room and it comes alive.
The default experience is deliberately gentle. Machines link up and configure themselves, and plain-language messages tell you what is happening. The realistic layer, with tuning, manual and cascade modes, NPSH limits and pressure trips, sits underneath for players who want to go deeper.
Liquids, Valves and Vessels
- Centrifugal pumps, pipes and tanks, with friction losses on long runs and cavitation on starved pumps
- Hand valves, check valves, drain valves and control valves
- Drums and IBCs you can carry around, dyed in any colour
- An 8x8x6 floating roof tank holding 8000 buckets, with a roof that rises and sinks and that you can walk on
Control and the Control Room
Transmitters measure level, flow and pressure. Drop a DCS controller against a tank and it finds its own valve and holds the level at 50 percent. Open the faceplate to change the setpoint, tune the PID, or switch between AUTO, MAN and CAS. The DCS console gives you an overview, five-minute trends and an ISA-style alarm list for everything within 32 blocks.
Then build the room around it. Video walls of up to 8x6 blocks show the overview, the alarms, the trends or your live P&ID. An amber alarm beacon turns and sounds until someone acknowledges it. An emergency stop shuts the whole plant down at once. There is even a printer that spits out the alarm log as a book for the shift handover, plus desks, chairs, coffee and a wall clock.
Power, Gases and the Refinery
Power starts small with a Stirling engine and a biogas generator, then climbs through a coal-fired boiler and steam turbine, where steam builds genuine pressure and an unprotected boiler bursts. Oil and gas burners, a diesel generator, a hydrogen fuel cell, a 30-block wind turbine and a million-FE battery bank round out the ladder. Cables share FE evenly and work with other mods' generators too.
Gases are counted in mB at 1 bar with real pressure. An electrolyser splits water into hydrogen and oxygen, a nitrogen generator pulls nitrogen from the air, and a compressor pushes lines up to 200 bar. Oxygen piped into a boiler makes coal last longer, an ammonia reactor wants 100 bar like the real thing, and a fertilizer mixer grows every crop in a 3x3 at once.
The refinery is the centrepiece of the late game. A pumpjack nods on its well, an eleven-block distillation column splits crude into LPG, naphtha, kerosene, diesel and residue, and a forty-block flare stack burns whatever the plant cannot keep. Climb the caged ladder to the top platform, right under the flame.
Supported Versions and Loader
Setpoint runs on NeoForge. You need Minecraft 26.3 with NeoForge 26.3.0.95 or newer, or Minecraft 26.1.2 with NeoForge 26.1.2.109 or newer, which is the build used by All the Mods 11. Each Minecraft version has its own file, so pick the one that matches your instance before you download Setpoint.
If you would rather skip the manual file hunt, the foxygame.net launcher handles it for you: its add-on catalog lists Setpoint with the correct build already matched to your Minecraft version, so installation is a single click.
How to Install Setpoint for Minecraft
- Install NeoForge for your Minecraft version first
- Download Setpoint from the official project page, choosing the file that matches your game version
- Drop the jar into your mods folder
- Launch the game and check the Setpoint Handbook, which is given on first join
Everything in the mod has a tooltip, with Shift held for details, and there is a full advancement tab to follow. Jade support shows equipment status when you look at a machine, and JEI lists every recipe with a dedicated tab per machine. Pack makers get configs for generator output, Hookonium ore and the showcase command, plus common tags so other mods' crude oil, diesel and steam work in Setpoint machines and vice versa.
Final Thoughts
Setpoint is one of the few mods that rewards patience with something that feels genuinely alive: a plant that runs, alarms, trips and recovers while you watch it from a chair in the control room. Start with a pump, a tank and a controller, learn the faceplate, and let the P&ID tell you what to build next. Before long you will be tuning loops and cursing a cavitating pump like a real operator.
===ARTICLE===